manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 219

PROCEDURE

1

If necessary, operate the turning gear to move the piston to BDC.

2

If the depth of the lubricating grooves (001, 

Figure 7-8

) has decreased to less than

1.5 mm, do as follows:

CAUTION

When you remove sharp edges, make sure that you keep the initial shape
of the lubricating grooves.

2.1

Use an oil stone or an emery cloth to get the lubricating grooves back to their
initial depth.

3

Fully clean the lubricating grooves and the bore of the cylinder liner.

4

Remove unwanted particles.

5

Manually operate the cylinder lubrication to flush unwanted material from the cylinder
liner.

Fig 7-8

 Lubricating grooves - grind

CLOSE UP

•

None

X82-B

AA00-2124-00AAA-655B-A

Maintenance Manual

Cylinder liner - grind the lubricating groove

Winterthur Gas & Diesel Ltd.

- 219 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands