WinGD X82-B Maintenance Manual Download Page 99

Page: 99 / 841

PROCEDURE

Read the data in

3.1 Lifting tools

General Guidelines for Lifting Tools.

Operate the turning gear to turn the crank to the exhaust side approximately 90° after
TDC.

Lock the turning gear to prevent movement.

Install the platform, refer to the related procedure.

Set to off the main oil supply pumps.

Close the oil lubrication to the main bearing.

CLOSE UP

•

Remove the No. 1 bearing shell, refer to

6.2.2 Main bearing - bearing shell - No. 1 -

remove

X82-B

AA00-1132-00AAA-523A-A

Maintenance Manual

Main bearing - bearing shell - No. 1 - prepare before removal

Winterthur Gas & Diesel Ltd.

- 99 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands