manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 567

PROCEDURE

1

Turn the power supply of E85 “off”.

2

Remove the top cover from the actuator terminal box. Make sure that no particles or
liquids enter the box.

3

Put a bridging wire between terminals 6 and 35. See number 1 in 

Figure 10-14

4

Put a bridging wire between terminals 5 and 43. See number 2 in 

Figure 10-14

5

Turn the power supply of E85 “on”.

6

Push the switch. See number 3 in 

Figure 10-14

NOTE:

If the switch is pushed correctly, the actuator moves to the maximum and
minimum position (self-adjustment).

NOTE:

The switch is very fragile. Make sure to use as little force as possible when
pushing it.

7

Wait until the movement of the fuel pump actuator stops.

8

Turn the power supply of E85 “off”.

9

Remove the two bridging wires. See numbers 1 and 2 in 

Figure 10-14

10

Re-attach the top cover of the actuator terminal box.

11

Turn the power supply of E85 “on”.

Fig 10-14  Calibration illustration

X82-B

AA00-5583-00AAA-273A-A

Maintenance Manual

Fuel pump actuator - calibrate

Winterthur Gas & Diesel Ltd.

- 567 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands