WinGD X82-B Maintenance Manual Download Page 518

Page: 518 / 841

Remove the valve body (016) together with the spring (015).

Remove the two bolts (001) from the control valve (017).

Remove the control valve (019).

Remove the screw plug (003) together with the spring (002), valve (019) and piston
(018) from the control valve (017).

Remove the silencer.

Clean the items that follow:

•

Valve (003)

•

Piston (018)

•

Spring (002)

•

Springs (007) and (015)

•

Valve body (016)

•

Valve guide (013)

•

Valve (010)

•

Spindle (006).

If you find corrosion on the springs (007, 022 and/or 002) you must replace them.

Do a check of all gaskets and O-rings that you removed for damage. If you find damage,
replace the applicable gaskets and/or O-rings.

Do a check of the piston joint ring (008). If you find damage, replace the piston joint ring.

Do a check of the valve seats (011, 012). If necessary, grind the sealing surfaces.

X82-B

AA00-4325-00AAA-530A-A

Maintenance Manual

Shut-off valve for starting air - disassemble

Winterthur Gas & Diesel Ltd.

- 518 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands