manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 554

Fig 10-10  Pump plunger and bottom housing assembly

010

002

002

006

008

007

005

012

004

00430

001

011

003

003

009

013

9

To assemble the pump plunger and bottom housing, do the steps that follow:

9.1

Install the top spring carrier (005, 

Figure 10-10

) and the compression spring

(002).

9.2

Put the plunger (003) into the bottom spring carrier (006).

9.3

Apply clean diesel oil to the pump plunger (003).

9.4

Put the pump plunger (003) and the bottom spring carrier (006) in position in the
top housing (007). Make sure that the two drivers of the pump plunger (003)
engage with the regulating sleeve (004).

9.5

Apply oil to the new O-ring (008).

9.6

Put the O-ring (008) on the top housing (007).

9.7

Put the bottom housing (009) on to the top housing (012).

9.8

Tighten equally the Allen screws (013) to compresses the compression spring
(002).

9.9

Make sure that the toothed rack (011) moves freely.

X82-B

AA00-5556-00AAA-710A-A

Maintenance Manual

Fuel pump - assemble

Winterthur Gas & Diesel Ltd.

- 554 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands