manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 177

Fig 6-35

 Thrust pad - removal

NOTE:

If some of the thrust pads are removed, the remaining thrust pads will keep the
crankshaft in position. If all thrust pads from the same side are removed, for
example all the astern pads, the crankshaft can move.

23

To prevent crankshaft movement, do as follows:

X82-B

AA00-1203-00AAA-520A-A

Maintenance Manual

Thrust bearing - remove the pads

Winterthur Gas & Diesel Ltd.

- 177 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands