manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 221

PROCEDURE

WARNING

Before you operate the turning gear, make sure that no personnel are near the flywheel,
or in the engine.

CAUTION

When you polish the scavenge ports, make sure that you do not cause damage to the
running surface of the cylinder liner.

1

If necessary, operate the turning gear to move the piston to get access to the scavenge
ports.

2

Use emery cloth to polish the surfaces of the scavenge ports (

Figure 7-9

). Make sure

that you keep the shape of the scavenge ports the same as those shown.

3

Remove unwanted particles from the scavenge space.

Fig 7-9

 Scavenge ports - grind

CLOSE UP

•

None

X82-B

AA00-2124-00AAA-655C-A

Maintenance Manual

Cylinder liner - grind the scavenge ports

Winterthur Gas & Diesel Ltd.

- 221 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands