WinGD X82-B Maintenance Manual Download Page 306

Page: 306 / 841

Fig 7-46

Exhaust valve - disassemble

Remove the guide bush.

3.1

Remove the Allen screws (001,

Figure 7-47

3.2

Remove the distance ring (003).

3.3

Remove and discard the rod joint ring (004).

3.4

Put the two jack screws (008) into the two threads of the guide bush flange
(003).

3.5

Turn equally the two jack screws (008) to push up the guide bush (007).

3.6

Remove the guide bush (007).

3.7

Measure the inner diameter of the guide bush (007).

3.8

Compare the measurement with the values given in section

3.3 Clearances -

general

X82-B

AA00-2751-00AAA-530A-A

Maintenance Manual

Exhaust valve - disassemble

Winterthur Gas & Diesel Ltd.

- 306 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands