WinGD X82-B Maintenance Manual Download Page 627

Page: 627 / 841

PROCEDURE

If the exhaust valve control unit (VCU) is a new item, carefully remove it from its
package.

Use oil to clean the VCU (005,

Figure 10-42

Remove the blanks from the ports in the VCU (005).

Fig 10-42 Exhaust valve control unit - install

001

002

003

004

005

006

007

008

00402

Clean the seating surfaces of the VCU (005) and the holder (006).

Make sure that the mating surfaces of the holder (006) and the VCU (005) have no
damage (for example no dents or no raised areas).

X82-B

AA00-5612-00AAA-720A-A

Maintenance Manual

Exhaust valve control unit (VCU) - install

Winterthur Gas & Diesel Ltd.

- 627 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands