WinGD X82-B Maintenance Manual Download Page 250

Page: 250 / 841

Fig 7-24

Cylinder cover, exhaust valve cage and water guide jacket (example)

Attach the engine room crane to the lifting tool (002,

Figure 7-25

Operate the engine room crane to lift the lifting tool (002).

Lower the lifting tool (002) on to the elastic studs (001).

Attach the lifting tool (002) to the elastic studs (001) with the round nuts (005).

Operate the engine room crane to lift and move the cylinder cover (003) to an applicable
area.

Lower the cylinder cover (003) on to an applicable support (006).

X82-B

AA00-2708-00AAA-520A-A

Maintenance Manual

Cylinder cover - remove

Winterthur Gas & Diesel Ltd.

- 250 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands