WinGD X82-B Maintenance Manual Download Page 95

Page: 95 / 841

6 Group 1 - Engine frame and bearings

6.1

Foundation bolts

6.1.1

Bedplate - do a check of the foundation bolts. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2

Main bearing - bearing shell number 1

6.2.1

Main bearing - bearing shell - No. 1 - prepare before removal. . . . . . . . . . . . . . .

6.2.2

Main bearing - bearing shell - No. 1 - remove. . . . . . . . . . . . . . . . . . . . . . . . . . . .

100

6.2.3

Main bearing shell - No.1 - do a check. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

108

6.2.4

Main bearing - bearing shell - No. 1 - install. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

110

6.3

Main bearing - bearing shell number 2 to #

6.3.1

Main bearing - bearing shell - No. 2 to # - prepare before removal. . . . . . . . . .

118

6.3.2

Main bearing - bearing shell - No. 2 to # - remove. . . . . . . . . . . . . . . . . . . . . . . .

120

6.3.3

Main bearing shell - No.2 to # - examine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

130

6.3.4

Main bearing - bearing shell - No. 2 to # - install. . . . . . . . . . . . . . . . . . . . . . . . .

132

6.4

Main bearing cover - No. 1

6.4.1

Main bearing cover - No.1 - remove. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

140

6.4.2

Main bearing cover - No.1 - install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

146

6.5

Main bearing cover - No. 2 to #

6.5.1

Main bearing cover - No. 2 to # - remove. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

152

6.5.2

Main bearing cover - No. 2 to #- install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

160

6.6

Thrust bearing

6.6.1

Thrust bearing - examine the housing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

166

6.6.2

Thrust bearing - do a check of the axial clearance with a dial gauge. . . . . . . .

168

6.6.3

Thrust bearing - do a check of the axial clearance with a inside micrometer.

170

6.6.4

Thrust bearing - remove the pads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

174

6.6.5

Thrust bearing - install the pads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

180

6.7

Engine stays

6.7.1

Engine stays (friction shims) - do a check of the pre-tension. . . . . . . . . . . . . . .

186

6.7.2

Engine stays (hydraulic) - do a check of the oil pressure. . . . . . . . . . . . . . . . . .

188

6.8

Tie rod

6.8.1

Tie rod - do a check of the pre-tension. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

190

6.8.2

Tie rod - remove. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

192

6.8.3

Tie rod - install. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

194

X82-B

Maintenance Manual

Winterthur Gas & Diesel Ltd.

- 95 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands