manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 188

6.7.2

Engine stays (hydraulic) - do a check of the oil pressure

Periodicity

Description

Months

1

Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

8.0 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Intermediate

2

Support equipment

Description

Part No.

CSN

QTY

None

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Injury Hazard: Hydraulic tools can cause injury to personnel. Always put on gloves, a
face shield and safety goggles when you do work with hydraulic tools.

PRELIMINARY OPERATIONS

•

The engine must be stopped and made safe for maintenance, refer to section 

4.1 Do

maintenance work - general procedure

X82-B

AA00-1715-00AAA-360B-A

Maintenance Manual

Engine stays (hydraulic) - do a check of the oil pressure

Winterthur Gas & Diesel Ltd.

- 188 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands