manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 146

6.4.2

Main bearing cover - No.1 - install

Periodicity

Description

Unscheduled
Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

2.0 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Basic

AR

Support equipment

Description

Part No.

CSN

QTY

Spur-geared chain block,
2500kg

94017-028

1

Thrust device

94110

1

Lug

94116C

1

Shackle 6500 kg

94019K

1

Shackle 2000 kg

94019G

1

Thrust device

94110

1

HP oil pump

94931

1

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

Main bearing cover

1

SAFETY PRECAUTIONS

•

None

PRELIMINARY OPERATIONS

•

The bearing shell must be installed, refer to section 

6.2.4 Main bearing - bearing shell -

No. 1 - install

•

The work area and all tools and equipment must be clean and in good condition.

X82-B

AA00-1132-01AAA-720A-A

Maintenance Manual

Main bearing cover - No.1 - install

Winterthur Gas & Diesel Ltd.

- 146 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands