WinGD X82-B Maintenance Manual Download Page 144

Page: 144 / 841

Fig 6-16

Bearing cover

WCH03014

00612

001

002

003

004

Attach the shackle 94019K (004,

Figure 6-17

) to the lug 94116C (003).

Attach engine room crane to the shackle 94109K (004).

Operate the engine room crane to put a light tension on the chain.

Remove the chain block (002) from the lug 94116C (003).

Operate the engine room crane to move the bearing cover on to an applicable surface.

Remove the engine room crane from the shackle (004).

X82-B

AA00-1132-01AAA-520A-A

Maintenance Manual

Main bearing cover - No.1 - remove

Winterthur Gas & Diesel Ltd.

- 144 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands