WinGD X82-B Maintenance Manual Download Page 309

Page: 309 / 841

PROCEDURE

Mark the position of the valve seat (001,

Figure 7-48

) in the valve cage.

Turn the valve cage (002) until the valve seat (001) points up.

Carefully put the valve cage (001) on to an applicable wooden support (003).

Install the top two halves of the valve seat tool (005) into the groove of the valve seat
(001).

Install the bottom two halves of the valve seat tool (005) into the groove of the valve
cage (002).

Turn equally the three jack screws (004) to push out the valve seat (001) from the valve
cage (002).

Remove and discard the O-ring (006).

Remove the valve seat tool (005).

Fig 7-48

Valve seat - remove

00726

001

006

001

002

003

004

005

002

CLOSE UP

•

None

X82-B

AA00-2751-01AAA-520A-A

Maintenance Manual

Exhaust valve - remove the seat (recommended procedure)

Winterthur Gas & Diesel Ltd.

- 309 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands