manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 709

PROCEDURE

1

Put an oil tray under the applicable hydraulic pipe (004, 

Figure 13-4

).

2

Loosen the screws (008) on the flange (003) to drain the applicable hydraulic pipe (004)
through the check bore (006) in the housing of the exhaust valve control unit (VCU)
(002).

3

Remove the six screws (010) from the flange (005).

4

Carefully move the flange (005) away from the top housing (001).

5

Remove the six screws (008) from the flange (003).

6

Carefully move the flange (003) away from the VCU (002).

7

Carefully remove the hydraulic pipe (004).

8

Apply protection to the sealing faces (007, 009) to prevent damage and contamination.

X82-B

AA00-8460-00AAA-520A-A

Maintenance Manual

Hydraulic pipe exhaust valve - remove

Winterthur Gas & Diesel Ltd.

- 709 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands