WinGD X82-B Maintenance Manual Download Page 652

Page: 652 / 841

Fig 11-12 Auxiliary blower (driving end) move

2.17

Attach the shackle (002,

Figure 11-13

) to the strut (001).

2.18

Attach the spur-geared chain block (003) to the shackle (002) and the two slings
(007).

2.19

Operate the chain blocks (002, 010) to move the electric motor (006) into the
casing.

2.20

Attach the electric motor (006) to the flange (004) with the bolts.

2.21

Attach the electric motor (006) to the support (005) with the bolts.

2.22

Connect the electrical connection to the electric motor (006).

X82-B

AA00-6545-00AAA-720A-A

Maintenance Manual

Auxiliary blower - install

Winterthur Gas & Diesel Ltd.

- 652 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands