manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 379

PROCEDURE

1

If it necessary to move the connecting rod away from the area, do 

Step 1.5

 to 

Step 1.15

:

1.1

Read the applicable safety precautions.

1.2

Put on the applicable personal protective equipment.

1.3

Attach two shackles (005, 

Figure 8-22

) to the positions shown.

1.4

Attach the spur-geared chain block (002, 006) to the connecting rod (003) and
the engine room crane.

1.5

Operate the engine room crane to lift and move the connecting rod to the
applicable area.

1.6

Lower the connecting rod (003) on to the floor.

1.7

Remove the engine room crane from the chain blocks (002, 006)

1.8

Attach the two chain blocks (002 and 006) to the top platform and the shackles
(005).

1.9

Lift the connecting rod (003) a small distance.

1.10

Attach two more shackles (009) to the top platform.

1.11

Attach two more chain blocks (007, 008) to the connecting rod (003) and
shackles (009) as shown in step B.

1.12

Attach and remove the chain blocks (002, 006, 007, 008) and shackles (005,
009) as given in 

Step 1.11

 to continue to move the connecting rod to the

applicable position for installation (step C).

1.13

Lower the connecting rod (003) on to the floor.

1.14

Remove the chain blocks and the shackles.

1.15

Continue the installation procedure from 

Step 2

.

X82-B

AA00-3303-00AAA-720A-A

Maintenance Manual

Connecting rod - install

Winterthur Gas & Diesel Ltd.

- 379 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands