WinGD X82-B Maintenance Manual Download Page 134

Page: 134 / 841

PROCEDURE

Bearing shell - install

1.1

NOTE:

The bearing shell has the mark DRIVING END and must be installed in
the correct position.

Make sure that the items that follow are clean and in good condition:

•

The crankshaft pin

•

The girder bore for the bearing shell

•

The bearing shell.

1.2

Apply a very thin layer of Molykote paste G to the rear face of the bearing shell
(002,

Figure 6-11

X82-B

AA00-1132-00AAB-720A-A

Maintenance Manual

Main bearing - bearing shell - No. 2 to # - install

Winterthur Gas & Diesel Ltd.

- 134 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands