WinGD X82-B Maintenance Manual Download Page 135

Page: 135 / 841

Fig 6-11

Bearing shell - move

1.3

Make sure that the crankshaft and the running surface of the bearing shell (002)
are clean and fully lubricated with clean engine oil.

1.4

Attach the lifting tool (001) to the bearing shell (002).

X82-B

AA00-1132-00AAB-720A-A

Maintenance Manual

Main bearing - bearing shell - No. 2 to # - install

Winterthur Gas & Diesel Ltd.

- 135 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands

WinGD X82-B, Maintenance Manual

Search results

Summary of Contents for X82-B

Reviews:

Brands by name

Popular brands