manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 22

1.1

Maintenance Manual - change record

Tab 1-1

 Change record

Data module code, issue

Chapter number - technical name

Reason for change

Status

New issue 001, 2020-10

All data modules

n/a

Initial issue of the fully new structured Maintenance Manual. The existing Maintenance Manual
published on 2018-12 is no more applicable.

X82-B

AA00-0000-00AAA-003B-A

Maintenance Manual

Maintenance Manual - change record

Winterthur Gas & Diesel Ltd.

- 22 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands