manualshive.com logo in svg

WinGD X82-B, Maintenance Manual

Share
Download
WinGD X82-B Maintenance Manual Download Page 86

4.3

Loosen a round nut with a pre-tensioner

Periodicity

Description

Unscheduled
Duration for performing preliminary requirements

0.0 man-hours

Duration for performing the procedure

1.0 man-hours

Duration for performing the requirements after job completion

0.0 man-hours

Personnel

Description

Specialization

QTY

Engine crew

Intermediate

1

Support equipment

Description

Part No.

CSN

QTY

HP oil pump

94931

pc 1

HP hose

A/R

pc 1

Hydraulic unit

94942

pc 1

Round bar - kit

94005

pc 1

Pre-tensioner

A/R

A/R

Supplies

Description

QTY

None

Spare Parts

Description

Part No.

CSN

QTY

None

SAFETY PRECAUTIONS

WARNING

Injury hazard: Hydraulic tools can cause injury to personnel. Always put on gloves, a
face shield and safety goggles when you do work with hydraulic tools.

PRELIMINARY OPERATIONS

•

The engine must be stopped.

X82-B

AA00-0000-00AAA-510A-A

Maintenance Manual

Loosen a round nut with a pre-tensioner

Winterthur Gas & Diesel Ltd.

- 86 -

Issue 001 2020-10

Summary of Contents for X82-B










































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands