Strasbaugh 6DS-SP Operation Manual Download Page 524 | Manualshive

Page: 524 / 1562

background image

Maintenance

Model 6DS-SP Planarizer

9 - 16

Version 4.0 - February 1998

TOOLS AND PARTS RECOMMENDED

•

6DS-SP ACC 72 Carrier Tool Kit - Item #218327

Note:

The Carrier Tool Kit includes the Carrier Adjusting Tool Assembly,

detailed immediately below.

Carrier Adjusting Tool Assembly (Strasbaugh Indicator Depth
Gauge Assembly) - Item #233595
Consisting of:

-

Mitutoyo Indicator Depth Gauge - Item #218198

-

Indicator Point, Flat Carbide - Item #218199

-

Indicator Depth Gauge Holder - Item #218201

•

6DS-SP ACC 30R (200 mm) Carrier Spare Parts Kit - Item #233556

•

6DS-SP ACC 45/45R (150 mm) Carrier Spare Parts Kit - Item #233555

•

6DS-SP ACC 58 (125 mm) Carrier Spare Parts Kit - Item #225134

•

6DS-SP ACC 56 (100 mm) Carrier Spare Parts Kit - Item #225133

•

6DS-SP ACC 57 (75 mm) Carrier Spare Parts Kit - Item #225132

Note:

Refer to the Appendix of this document for a bill of materials for
each of the six kits shown above.

•

plastic block with hole in center large enough to permit carrier top plate
quill socket to extend down through the block while the block supports the
top plate

•

6DS-SP Carrier Assembly Table - Item #220640

Note:

The Carrier Assembly Table includes the Bench Top Carrier Fixture,

listed below.

•

6DS-SP Bench Top Carrier Fixture - Item #219570

•

retaining ring plier

•

feeler gauge

•

1/4-in. socket wrench

«
...
522
523
524
525
526
...
»

Summary of Contents for 6DS-SP



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6DS-SP

Brand: BACtrack Pages: 13

Brand: TA Instruments Pages: 35

Brand: Bang & Olufsen Pages: 2

Sportsound SSR-300

Brand: Daktronics Pages: 42

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

Brand: IFM Pages: 175

Brand: IFM Pages: 5

Brand: lancer Pages: 3

Brand: lancer Pages: 12

Brand: R2 Pages: 26

Brand: Nederman Pages: 89

Brand: Nederman Pages: 71

Brand: Nederman Pages: 131

Brand: X-Cite Pages: 2

Brand: ZacUrate Pages: 2

Brand: ZacUrate Pages: 2

Brand: YOKOGAWA Pages: 75

HomeFill HF2POST6

Brand: Invacare Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands