Strasbaugh 6DS-SP Operation Manual Download Page 1340 | Manualshive

Page: 1340 / 1562

background image

STRASBAUGH, INC.

June 5, 1998

6DS-SP Software Ver 4.26.1

Page 3

Calibration/Configuration Menu Changes:

Calibration variable 100 "AGV present (0-no, 1-yes)" (new variable)

This variable must be set to "1" if the AGV option is present.
It must be set to "0" if the AGV option is absent.

Calibration variable 186 "Scrb data xfr(0-dsbl, 1, or 2)" (changed variable)

This variable must be set to "2" if the AGV option is present which includes a Yuasa
scrubber with a four byte data transfer. ("0" is disable and "1" is for a three byte data
transfer.)

Calibration variable 88 "Thruput unload/AGV up/dn top" (changed variable)
Calibration variable 89 "Thruput unload/AGV up/dn bot" (changed variable)

These two variables adjust the up/down positions of the robot at the AGV interface
station. (For a high throughput option configuration, they are used to adjust for the
throughput stations.)

Machine Setup Menu Changes:

The Machine Setup menu will show the following choices for the AGV option:

Wafer source (in auto cycle)

Cassette
AGV intrfc

During an auto cycle,

Cassette

will cause wafers

to be taken from the send cassette.

AGV intrfc

will cause wafers to be accepted from the AGV
station.

Recipe source if using AGV

Oper/GEM
AGV intrfc

This selects how recipes are selected.

If set to

Oper/GEM

, the recipe will be whatever

was last selected by the operator or by GEM.
Recipe selections from the AGV interface are
ignored.

AGV intrfc

will cause recipes to be selected by

AGV interface data when using the "Auto" cycle.
Any previously selected recipe will be
superseded by the AGV recipe. If using the
scrubber transfer mode, the currently showing
recipe is used and AGV recipes will not be
selected regardless of this setting.

«
...
1338
1339
1340
1341
1342
...
»

Summary of Contents for 6DS-SP



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6DS-SP

Brand: Unex Pages: 5

Brand: Jackson Pages: 2

Cell Saver Elite+

Brand: Haemonetics Pages: 230

Brand: Parker Pages: 24

Porta PlumeSafe 604

Brand: Buffalo filter Pages: 75

Brand: Hettich Pages: 104

Shark Beam FX one

Brand: SHOWTEC Pages: 32

Brand: Festo Pages: 94

Brand: HE-VA Pages: 48

Brand: Zeta Pages: 2

Brand: R.V.R. Elettronica Pages: 38

Brand: Studio Technologies Pages: 23

Brand: KW Hydraulik Pages: 36

Brand: SaMASZ Pages: 28

Brand: K-SPORT Pages: 6

Brand: Laversab Pages: 103

Brand: Omcan Pages: 12

Brand: Titan Fitness Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands