Strasbaugh 6DS-SP Operation Manual Download Page 943 | Manualshive

Page: 943 / 1562

background image

Strasbaugh Troubleshooting

Version 4.0 - February 1998 13 - 31

ALARM MESSAGES

Error Messages

All error messages except

Elevator Section Operator Door Open

and

Polish

Section Operator Door Open

are accompanied by alarm sounds.

The control computer displays one error message at a time; if multiple
problems exist (typically unlikely), correct the one indicated by the first
message. The next message will then appear. After that problem is
resolved, the error message for the second problem will be displayed.

Alarms

During an auto cycle, whenever the controller senses a machine parameter
out of range of the set limits (either above the programmed high limit or
below the programmed low limit set at the Alarm Parameters Menu), the
alarm on the control panel will sound until the parameter returns to within
the set limits

OR

the operator halts the cycle.

While the alarm sounds, an alarm message displays at the bottom of the Auto
Polish Cycle menu screen.

An alarm condition does not abort the machine cycle automatically.

The alarm is a warning device to the operator indicating a fault according to
programmed parameter values.

The Alarm Parameters Menu displays the current programmed upper (high
limit) and lower (low limit) alarm conditions in percentage of error for ten
machine functions.

For more information on the Alarm Parameters Menu, refer to the Machine
Setup chapter of the

6DS-SP Operations

manual.

«
...
941
942
943
944
945
...
»

Summary of Contents for 6DS-SP



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6DS-SP

ImageQuant LAS 4000

Brand: GE Pages: 86

Brand: GE Pages: 160

Brand: GE Pages: 134

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Brand: Makita Pages: 8

Brand: VECTECH Pages: 5

Brand: YYZ Lighting Pages: 3

Brand: Camp Safety Pages: 118

Brand: Ultrafast Systems Pages: 39

Brand: Mackworth Pages: 2

Brand: Ocmis Irrigazione Pages: 100

Brand: Jackson Pages: 2

Cell Saver Elite+

Brand: Haemonetics Pages: 230

Brand: Goobay Pages: 6

Brand: Feniex Pages: 5

Brand: IKEA Pages: 24

mocon AQUATRAN 3/38

Brand: Ametek Pages: 85

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands