manualshive.com logo in svg

Strasbaugh 6DS-SP, Operation Manual

The Strasbaugh 6DS-SP Operation Manual is a crucial resource for understanding how to operate and maintain this advanced polishing system. You can easily download this manual for free from our website. Ensure smooth functioning of your equipment by having the manual on hand at all times.

Share
Download
background image

Strasbaugh

      Machine Setup

Version 4.0 - February 1998

4 - 31

POLISH AND CONDITION FORCE UNITS AND DIAMETER
ENTRY:

Polish and conditioning force units and wafer diameter and conditioning
device diameter are entered in the Machine Parameters Menu and
Conditioning/Cleaning Parameters Menu respectively.

This permits the units and diameters to be saved as part of the recipe.

The diameter is not used if "lbs" is used for force.  If "psi" is used and zero is
entered for the diameter, displays will show "Wfr Dia?" or "Dev Dia?" to
warn that no diameter is entered.

Also, if changing between "lbs" and "psi", no recipe values will be changed.
For example, 7 psi would become 7 lbs if the units were changed.

"SINGLE" SWEEP STYLE CHOICE:

The choice 

Single 

is among the 

One way and Two way 

sweep style choices

in the Conditioning/Cleaning Menu.  If 

Single 

is selected, the value in the

Conditioning Cycles 

choice will specify a number of single sweep

traverses.  For example, if 

Conditioning Cycles 

is set to "3" and 

Sweep

Start 

is set to 

Outer, 

the arm swill sweep three times (out to in, in to out,

and out to in).

PRE OR POST PAD CONDITIONING:

Pre or post conditioning can be set with the 

Pre/Post Conditioning 

choice.

If set to 

Pre Cond, 

conditioning cycles will occur before polishing cycles. If

set to 

Post Cond, 

conditioning cycles will occur after polishing cycles.

Summary of Contents for 6DS-SP



























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 6DS-SP

FagronLab FG User Manual preview
FG
Brand: FagronLab Pages: 16
NARGESA BM25 Manual preview
BM25
Brand: NARGESA Pages: 50
Taylor 490 Operator Training preview
490
Brand: Taylor Pages: 70
Raith 150 System Operation Manual preview
150
Brand: Raith Pages: 26
Kane 501C Manual preview
501C
Brand: Kane Pages: 16
SALUDA MEDICAL Evoke Clinical Manual preview
Evoke
Brand: SALUDA MEDICAL Pages: 61
QBC Diagnostics Star Operators & Service Manual preview
Star
Brand: QBC Diagnostics Pages: 65
Bacharach Fyrite Tech 50 Operating And Maintenance Instructions Manual preview
Fyrite Tech 50
Brand: Bacharach Pages: 48
Haki 564 User Manual preview
564
Brand: Haki Pages: 24
Dakota Digital VHX-66F-BRO Installation preview
VHX-66F-BRO
Brand: Dakota Digital Pages: 5
DB Industries DELTA 2 User Instructions preview
DELTA 2
Brand: DB Industries Pages: 60
vc999 K5 Operating Manual preview
K5
Brand: vc999 Pages: 55
Salsbury Industries 3700 Series Manual preview
3700 Series
Brand: Salsbury Industries Pages: 4
Eagle Eye SG-1000 User Manual preview
SG-1000
Brand: Eagle Eye Pages: 21
Labomed Magna User Manual preview
Magna
Brand: Labomed Pages: 67
rbd instruments IG2 Manual preview
IG2
Brand: rbd instruments Pages: 18
Cooper IB520081ML Installation Instructions Manual preview
IB520081ML
Brand: Cooper Pages: 10
Korg HT-10 Owner'S Manual preview
HT-10
Brand: Korg Pages: 32

Brands by name

Popular brands

Load more brands