Strasbaugh 6DS-SP Operation Manual Download Page 504

Page: 504 / 1562

Maintenance

Model 6DS-SP Planarizer

8 - 14

Version 4.0 - February 1998

180-DAY

PREVENTIVE

MAINTENANCE SCHEDULE

SUBJECT

ACTION

•

Bridge

•

Clean Dry Air (CDA) or Nitrogen

•

Conditioning Device Rotation Gearbox
Oil

•

Coolant Flow Transmitter

•

D. I. Water

•

Elevators

•

Leak Detect Sensors

•

Polish Table Gearbox Oil

•

Resistive Thermal Device (aka.
Thermocouple in previous
documentation)

•

Robot

•

Slurry System

Check and calibrate bridge position.
Inspect and replace drive belt if needed.

Check flow rate.

Check oil level and fill if required. (Use 9
ozs. AGMA No. 8 or equivalent.)

Check and calibrate. (Refer to Signet
manufacturer’s data.)

Check flow rate.

Check drive belts and replace as needed.

Check and adjust.

Change. (Use 19 pts. AGMA No. 8 or
equivalent.)

Check and calibrate.

Check drive belts; replace as needed.
Check and adjust robot vacuum sensor.

Check and adjust slurry low sensors.
Check and calibrate peristaltic pumps.
Replace peristaltic pump tubes.

Summary of Contents for 6DS-SP
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 6DS-SP

Reviews:

Related manuals for 6DS-SP

Brands by name

Popular brands

Strasbaugh 6DS-SP, Operation Manual

Search results

Summary of Contents for 6DS-SP

Reviews:

Related manuals for 6DS-SP

Brands by name

Popular brands