Shihlin SA3 Series, User Manual

Page: 217 / 423

Communication parameter group 07
PARAMETER DESCRIPTION 215
Step 2: After receive and processing the data without error, inverter will send a reply to upper controller:
Mode Start Address Function Start address Write data Check Stop
ASCII H3A H30 H31 H30 H36 H30H30 H43 H33 H31 H33 H38 H38 H39 H42 0D 0A
RTU >=10ms 01 06 00 C3 13 88 74 A0 >=10ms
Example 4. Upper controller read parameters 01-10(P.0), 01-00(P.1), 01-01(P.2), 01-03(P.3), 04-00~04-02(P.4~P.6),
01-06~01-07(P.7~P.8), 06-00(P.9),10-00~10-01(P.10~P.11).
Step 1: Upper controller sends message to inverter for reading 01-10(P.0), 01-00(P.1), 01-01(P.2), 01-03(P.3),
04-00~04-02(P.4~P.6), 01-06~01-07(P.7~P.8), 06-00(P.9), 10-00~10-01(P.10~P.11) value. Start address
is H0000.
Mode Start Address Function Start address Number of registers Check Stop
ASCII H3A H30 H31 H30 H33 H30H30 H30 H30 H30 H30 H30 H43 H46 H30 0D 0A
RTU >=10ms 01 03 00 00 00 0C 45 CF >=10ms
Step 2: After receive and processing the data without error, inverter will send a reply to upper controller:
Mode Start Address Function Number of data read Read out data Check Stop
ASCII H3A H30 H31 H30 H33 H31 H38 …12×4 char 2char 0D 0A
RTU >=10ms 01 03 18 …12×2 byte 2byte >=10ms
Example 5. Upper controller write parameters 01-10(P.0), 01-00(P.1), 01-01(P.2), 01-03(P.3), 04-00~04-02(P.4~P.6),
01-06~01-07(P.7~P.8), 06-00(P.9), 10-00~10-01(P.10~P.11).
Step 1: Upper controller sends message to inverter for writing 01-10(P.0), 01-00(P.1), 01-01(P.2), 01-03(P.3),
04-00~04-02(P.4~P.6), 01-06~01-07/P.7~P.8, 06-00(P.9),10-00~10-01(P.10~P.11).
Mode Starting Address Function Start address
Number of
registers Data
volume
Write-in data Check Stop
ASCII H3A H30 H31 H31 H30
H30
H30 H30
H30 H30
H30 H30
H43
H31 H38 …N×4 char 2char 0D 0A
RTU >=10ms 01 10 00 00 00 0C 18 …N×2 byte 2byte >=10ms
Step 2: After receive and processing the data without error, inverter will send a reply to upper controller:
Mode Start Address Function Start address Number of registers Check Stop
ASCII H3A H30 H31 H31 H30 H30H30 H30 H30 H30 H30 H30 H43 H45 H33 0D 0A
RTU >=10ms 01 10 00 00 00 0C 00 18 >=10ms
Note: In above examples, parameters 02-15(P.195)reading and writing are all using P parameter mode. To use
parameter group mode, please note the difference in address. Please refer to the communication command list for
relevant contents.