System parameter group 00
PARAMETER DESCRIPTION 86
Group
No.
Name
Group
No.
Name
02-45
P.64
Terminal AM1 output signal selection
04-14
P.149
Speed15
02-46
P.191
Terminal AM1 output gain
04-19
P.131
Programmed operation mode speed 1
02-47
P.190
Terminal AM1 output bias
04-23
P.135
Programmed operation mode speed 5
02-48
P.538
Terminal AM2 output signal selection
04-24
P.136
Programmed operation mode speed 6
02-49
P.536
Terminal AM2 output gain
04-25
P.137
Programmed operation mode speed 7
02-50
P.535
Terminal AM2 output bias
04-26
P.138
Programmed operation mode speed 8
02-51
P.55
Maximum analog output frequency reference
06-17
P.261
Maintenance alarm function
06-40
P.288
Alarm record code query
02-52
P.56
Maximum analog output current reference
06-42
P.290
Alarm record message query
08-03
P.225
PID target value
02-55
P.592
PT100 thermistor voltage level 1
08-18
P.223 Reserved
02-56
P.593
PT100 thermistor voltage level 2
08-19
P.224 Reserved
02-59
P.187
FM calibration coefficient
10-19
P.230
Dwell frequency at acceleration
03-14
P.87 Digital input logic
10-21
P.232
Dwell frequency at deceleration
04-00
P.4
Speed1(high speed)
10-45
P.267
Regeneration avoid function selection
04-01
P.5
Speed2(medium speed)
10-46
P.268
Regeneration avoid action voltage level
04-02
P.6
Speed3(low speed)
10-47
P.269
Regeneration avoid function DC bus voltage
detection sensitivity at deceleration
04-03
P.24
Speed4
10-48
P.270
Regeneration avoid frequency compensation
value
04-04
P.25
Speed5
04-05
P.26
Speed6
10-49
P.271
Regeneration avoid
voltage gain coefficient
04-06
P.27
Speed7
04-07
P.142
Speed8
10-50
P.272
Regeneration avoid frequency gain coefficient
04-08
P.143
Speed9
10-55
P.780 PLC function selection
04-09
P.144
Speed10
10-56
P.781 PLC run
04-10
P.145
Speed11
10-58
P.783 PLC choose register to monitor
04-11
P.146
Speed12
11-12
P.401
Torque command
04-12
P.147
Speed13
14-05
P.605
Tension setting
04-13
P.148
Speed14
14-45
P.657
Linear speed setting
Most parameters cannot be written. (00-03（P.77）=“1”)
Exception
Parameters below can be written.
Group
No.
Name
Group
No.
Name
00-03
P.77
Selection of parameters write protection
00-16
P.79
Operation mode selection
When running, the parameters below can be written. (00-03(P.77)=“2”)
Exception
When running, the parameters below cannot be written:
Group
No.
Name
Group
No.
Name
00-00
P.90
Inverter model
03-59
P.585 Monitor inverter digital input terminal state
00-01
P.188 Firmware version
00-11
P.72
Carrier frequency
03-60
P.586
Monitor inverter and Slot3 digital output
terminal state
00-15
P.78
Forward/reverse rotation prevention
selection
03-61
P.587 Monitor Slot2&3 digital input terminal state
00-16
P.79
Operation mode selection
00-26
P.125 Expansion card type
