Cisco Unified Communications Manager Configuration Manual Download Page 137

Page: 137 / 182

A-7

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Appendix A MIBs, RFCs, and SNMP Trap Messages for the Cisco TelePresence System

Peripheral Status Messages

ctpDVIPeripheralStatus—



Information about a single peripheral
attached through a DVI port.

Cable

•

plugged (1)—Peripheral cable is plugged.

•

loose (2)—Peripheral cable is loose.

•

unplugged (3)—Peripheral cable is unplugged.

•

unknown (4)—Cannot detect peripheral cable status.

•

internalError(5)—Internal error.

Power

•

on (1)—Peripheral power is on.

•

standby (2)—Peripheral power is in standby mode.

•

off (3)—Peripheral power is off.

•

unknown (4)—Cannot detect peripheral power status.

•

internalError (5)—Internal error.

Example

CISCO-TELEPRESENCE-MIB::ctpDVIPeripheralCableStatus.9.1 = INTEGER:

plugged(1)

Table A-3

Peripheral Status (continued)

Notification

Return Values

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands