Cisco Unified Communications Manager Configuration Manual Download Page 66

Page: 66 / 182

2-6

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Chapter 2 Configuring the Cisco Unified IP Phone for MIDlets

Configuring the Cisco Unified IP Phone

Always Use Prime Line for Voice
Message

Yes

Default.

Calling Party Transformation CSS

—

<None>

Geolocation

—

<None>

Check-Boxes

Use Device Pool Calling Party
Transformation CSS

—

Box is checked.

Ignore Presentation Indicators

Retry Video Call as Audio

Allow Control of Device from CTI

Logged Into Hunt Group

Remote Device

Protected Device

—

A new Softkey template without supplementary
service Softkeys must be used for a protected
phone.

Hot Line Device

—

A custom Softkey template without supplementary
service Softkeys must be used for a Hot line Device.

Note

When you are finished making changes, click Save to save your settings.

Table 2-1

Cisco Unified IP Phone 7975 Device Information (continued)

Field

Required?

Setting

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands