Cisco Unified Communications Manager Configuration Manual Download Page 134

Page: 134 / 182

A-4

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Appendix A MIBs, RFCs, and SNMP Trap Messages for the Cisco TelePresence System

Peripheral Status Messages

Table A-3

lists peripheral status messages.

Table A-3

Peripheral Status

Notification

Return Values

ctpPeripheralDescription

This object specifies a description of the attached peripheral. Peripheral description
may be the peripheral type, model and/or version information or a peripheral signal
description.

Reports the following system details:

•

Projector Product ID

•

IP Phone MIDlet information

•

Phone load and MIDlet version for phone status

ctpPeripheralCableCode

The textual convention identifies cable status of the attached peripheral through
HDMI.

•

plugged (1)—Peripheral cable is plugged.

•

loose (2)—Peripheral cable is loose.

•

unplugged (3)—Peripheral cable is unplugged.

•

unknown (4)—Cannot detect peripheral cable status.

•

internalError (5)—Internal error.

ctpPeripheralPowerCode

The textual convention identifies power status of the attached peripheral through
HDMI:

•

on (1)—Peripheral power is on.

•

standby (2)—Peripheral power is in standby mode.

•

off (3)—Peripheral power is off.

•

unknown (4)—Cannot detect peripheral power status.

•

internalError (5)—Internal error.

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands