Cisco Unified Communications Manager Configuration Manual Download Page 70

Page: 70 / 182

2-10

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Chapter 2 Configuring the Cisco Unified IP Phone for MIDlets

Configuring the Cisco Unified IP Phone

Extension Information

Table 2-7

describes fields found in the Extension Information section on the Phone Configuration page.

Note

Leave all fields unchanged.

Table 2-6

External Data Location Settings for CTS Release 1.7 and Later

Field

Setting

Information

Leave all fields blank to use the default.

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands