Cisco Unified Communications Manager Configuration Manual Download Page 120 | Manualshive

Page: 120 / 182

background image

6-12

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Chapter 6 Setting Up the Room to Use Cisco TelePresence Manager

Configuring IBM Domino for CTS-Manager

Step 1

Install and configure the Exchange 2007 server.

Step 2

Migrate the CTS-Manager User mailbox to the Exchange 2007 server.

Step 3

In CTS-Manager, go to Configure > Microsoft Exchange.

Step 4

Enter and apply the Exchange 2007 server configuration information. Once complete, the system will
reboot.

Step 5

After the system has rebooted, shut down the CTS-Manager server.

This is important so that users do not use the CTS-Manager during migration.

Step 6

Migrate all Cisco TelePresence endpoints to the Exchange 2007 server.

Step 7

Verify that all Cisco TelePresence endpoints are of the type “RoomMailbox.” This is required for
Auto-Accept to be enabled.

Step 8

After the migration is complete, add full access permission for the delegates to any proxy.

Configuring IBM Domino for CTS-Manager

Use the information in this section to create an account in IBM Domino for CTS-Manager.

Note

The CTS-Manager LDAP user and system administrator need read permission to the Domino Directory.
Use the information at the

Lotus Domino 7 Administrator Help

website for complete information.

Before You Begin

•

Internet password for this account must be set.

•

Provide an adequate mailbox quota for the CTS-Manager account—Cisco recommends setting up
an account with at least 1 GB of mailbox quota for a deployment of up to 50 rooms.

Procedure

To configure IBM Domino for CTS-Manager, follow these general steps:

Step 1

Log into the CTS-Manager account once to verify that it is set up correctly.

Step 2

Set CTS-Manager account read and edit permissions for each resource reservation database that contains
Cisco TelePresence room by doing the following:

a.

Select the specific resource reservation database and right click to select Database > Access
Control.

b.

Choose the account as specified below and set permissions per the instructions.

Step 3

Create a room resource in IBM Domino for each Cisco TelePresence or video conferencing room. Verify
the following if applicable:

•

Create a new resource reservation database

•

Create a new site profile document

•

Add Cisco TelePresence rooms for Domino.

•

Create the Resource Reservation database.

«
...
118
119
120
121
122
...
»

Summary of Contents for Unified Communications Manager























































































































































































Reviews:

No comments

Related manuals for Unified Communications Manager

Brand: JVC Pages: 92

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 3

Brand: Philips Pages: 18

VideoTracer DVT3120

Brand: Philips Pages: 26

Brand: Philips Pages: 15

Brand: Philips Pages: 22

Brand: Philips Pages: 21

Brand: Philips Pages: 34

Explorer VKR6878

Brand: Philips Pages: 34

Explorer VKR9010

Brand: Philips Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands