Cisco Unified Communications Manager Configuration Manual Download Page 144

Page: 144 / 182

A-14

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Appendix A MIBs, RFCs, and SNMP Trap Messages for the Cisco TelePresence System

Cisco TelePresence Call (CTPC) MIBs

Call Management System Response Code MIBs

Table A-7

lists Call Management System Response Code MIBs.

Remote Device Type MIBs

Table A-7

lists Remote Device Type MIBs.

Table A-11

Call Management System Response Code MIBs

MIB

Type

Attributes

ctpcMgmtSysSIPRespCode

Cisco Unified CM registration SIP response code. Notification is sent if
the Cisco Unified CM registration status changes.

Table A-12

Call Attributes MIBs

MIB

Type

Attributes

CtpcRemoteDeviceType

•

unknown (1)

•

other (2)

•

audioDevice (3)

•

videoLegacyDevice (4)

•

highDefinitionLegacyDevice (5)

•

singleTelepresence (6)

•

tripleTelepresence (7)

•

telepresenceMultipointSwitch (8)

•

telepresenceRecordingServer (9)

•

telepresenceTranscodingDevice (10)

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands