Cisco Unified Communications Manager Configuration Manual Download Page 131

Page: 131 / 182

A-1

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

A P P E N D I X

MIBs, RFCs, and SNMP Trap Messages for the
Cisco TelePresence System

Revised: September, 2010, OL-21851-01

Note

Use the information in this Appendix with the

SNMP Configuration Parameters

section of

“Configuring

a Cisco TelePresence Device” section on page 1-6

Contents

This chapter contains the following information:

•

CTS SNMP Trap Message Matrix, page A-1

•

Configuration Management Messages, page A-3

•

Peripheral Status Messages, page A-4

•

Event History Messages, page A-8

•

Trap Notification Messages, page A-9

•

Cisco TelePresence Call (CTPC) MIBs, page A-9

•

Supported Call States MIBs, page A-20

•

SNMP Objects Value Persistence, page A-21

•

SNMP Special Characters, page A-22

CTS SNMP Trap Message Matrix

Turning on a specific MIB enables an SNMP trap.

Table A-1

lists MIBs, RFCs, and SNMP trap messages

that are supported by the Cisco TelePresence System (CTS). SNMP MIB files can be found in the
following directories:

•

SNMP version 1 MIB files are in the v1 directory.

•

SNMP version 2 MIB files are in the v2 directory.

Note

For every MIB.my in the v2 directory, there is an SNMP version 1 MIB-V1SMI.my in the v1 directory.

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands