Cisco Unified Communications Manager Configuration Manual Download Page 151

Page: 151 / 182

A-21

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Appendix A MIBs, RFCs, and SNMP Trap Messages for the Cisco TelePresence System

SNMP Objects Value Persistence

SNMP objects are reset to pre-saved values when SNMPD is restarted. Supported objects are listed in

Table A-23

. Command-line interface (CLI) is used to preserve the pre-set values for the objects listed

in, as described in the

“SNMP Objects Value Persistence CLI” section on page A-21

SNMP Objects Value Persistence CLI

The following commands are supported in admin mode:

Tip

Remember to save your settings for reboot so that you do not have to load the entire code again.

Table A-23

SNMP Objects Value Persistence

Supported Devices and Applications

Object Type

CTS

—

•

CTMS/CTS-MAN objects

•

ciscoEnvMonEnableStatChangeNotif

•

ctpPeripheralErrorNotifyEnable

•

ctpSysUserAuthFailNotifyEnable

•

ctpPeripheralErrorHistTableSize

•

ctpSysUserAuthFailHistTableSize

•

ctpcStatNotifyEnable

•

ctpcMgmtSysConnNotifyEnable

•

ctpcStatMonitoredTable (all active rows)

•

ctpcStatEventHistTableSize

CTMS and CTS-Man

—

•

clogNotificationsEnabled

•

clogMaxSeverity

•

clogHistTableMaxLength

Command

Description

help utils snmp save

Saves a set of current SNMP object values. The saved values replace the
object default values when SNMPD is restarted.

snmp save help

help utils snmp reset

Resets SNMP default values. Current SNMP objects value will not be
affected. The default values are used the next time SNMPD is restarted.

snmp reset help

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands