Cisco Unified Communications Manager Configuration Manual Download Page 143

Page: 143 / 182

A-13

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Appendix A MIBs, RFCs, and SNMP Trap Messages for the Cisco TelePresence System

Cisco TelePresence Call (CTPC) MIBs

Call Receive and Transmit MIBs

Table A-7

lists Call Receive and Transmit MIBs.

Cisco Unified Communications Manager Call MIBs

•

Call Management Connection Status MIBs, page A-13

•

Call Management System Response Code MIBs, page A-14

Call Management Connection Status MIBs

Table A-7

lists Call Management Connection Status MIBs.

Table A-9

Call Receive and Transmit MIBs

MIB

Type

Attributes

ctpcTxFrameRate



ctpcRxFrameRate

New auxiliary stream to support 1fps, 5fps and 30fps that supports the
following new call states:

•

busy (17)

•

pause (18)

•

playback (19)

•

recording (20)

Table A-10

Call Management Connection Status MIBs

MIB

Type

Attributes

ctpcMgmtSysConnStatus

Displays the Cisco Unified CM registration status:

•

unknown (1)

•

other (2)

•

internalError (3)

•

notRegister (4)

•

registered (5)

•

registraionFailure (6)

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands