Cisco Unified Communications Manager Configuration Manual Download Page 69

Page: 69 / 182

2-9

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Chapter 2 Configuring the Cisco Unified IP Phone for MIDlets

Configuring the Cisco Unified IP Phone

For CTS Release 1.6 and Earlier

For CTS Release 1.7 and Later

Note

CTS Release 1.7 and later releases require MIDlets.

Table 2-5

External Data Location Settings for CTS Release 1.6 and Earlier

Field

Required
Non-MIDlets

Required for
MIDlets

Setting

Information

—

Yes

Leave blank to use the default.

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands