Cisco Unified Communications Manager Configuration Manual Download Page 61

Page: 61 / 182

C H A P T E R

2-1

Cisco Unified Communications Manager Configuration Guide for the Cisco TelePresence System

OL-21851-01

Configuring the Cisco Unified IP Phone for
MIDlets

Revised: December, 2010, OL-21851-01

Contents

This chapter describes how to configure and manage the Cisco Unified IP Phone and the Enhanced
Phone User Interface that uses Java

MIDlets

s on the Cisco Unified IP Phone.

This chapter contains the following information:

•

Important Notes, page 2-1

•

Configuring the Cisco Unified IP Phone, page 2-2

•

Uploading Files to the Cisco Unified CM TFTP Directory, page 2-14

•

Creating MIDlets IP Phone Service in Cisco Unified CM, page 2-16

•

Configuring MIDlets, page 2-14

•

Configuring a Remote Phone, page 2-18

•

Where to Go Next, page 2-20

Important Notes

See the following advisories and important notes that may affect system behavior:

•

MIDlets Software Releases, page 2-1

•

Cisco WebEx on the Cisco Unified CM, page 2-2

•

Adding a New Phone with MIDlets Capability, page 2-2

MIDlets Software Releases

MIDlets

is supported with Cisco Unified Communications Manager (Cisco Unified CM) Release 7.0.2,

7.1.2, 7.1.3, 7.1.3bSU2, and later releases). Cisco Unified CM also supports firmware release 8.0.

The supported

MIDlets

version is embedded in the software files that are available on the

Cisco Unified

Communications Manager Support

page at the following URL:



http://www.cisco.com/en/US/products/sw/voicesw/ps556/tsd_products_support_series_home.html

Summary of Contents for Unified Communications Manager























































































































































































Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands

Cisco Unified Communications Manager, Configuration Manual

Search results

Summary of Contents for Unified Communications Manager

Reviews:

Related manuals for Unified Communications Manager

Brands by name

Popular brands