Sices HS 315, Техническое руководство

Страница: 40 / 255

22 Technical Handbook
DIF.2063 Full override of protections. When the input is activated, all the protections (except for few,
see [1] ) which involve alarms or deactivations become
warnings.
DIF.2064
Override generator’s protections. When the input is “active”, all the protections for the generator,
which normally act as alarms or deactivation become mere
warnings
DIF.2071 Inhibit DPF regeneration. When the input is "active", the controller "prevents" the
regeneration of the particulate filter to the engine ECU. See
par. 8.5.5.8.
DIF.2072 Force DPF regeneration. When the input is "active", the controller requires the
regeneration of the particulate filter to the engine ECU. See
par. 8.5.5.8.
DIF.2241 Fuel pump in MAN-OFF mode. When the input is active, the mode of the fuel pump is forced
into “Manual-OFF”.
DIF.2242 Fuel pump in MAN-ON mode. When the input is active, the mode of the fuel pump is forced
into “Manual-ON”.
DIF.2243 Fuel pump in AUTO mode. When the input is active, the mode of the fuel pump is forced
into “Automatic”.
DIF.2271 Remote OFF. When this input is active, the operation mode of the controller
is forced into OFF-RESET and you cannot use the buttons on
the panel to change it.
NB: when this input is deactivated, if
there are no inputs configured with the functions DIF.2272
and DIF.2273, the operation mode returns to what it was
prior to the activation of the input
DIF.2272 Remote MAN. When this input is active, the operation mode of the controller
is forced into MAN and you cannot use the buttons on the panel
to change it.
DIF.2273 Remote AUTO. When this input is active, the operation mode of the controller
is forced into AUTO and you cannot use the buttons on the
panel to change it.
DIF.2321 Full charge. When this input is active during a charge cycle, the controller
performs a full charge (thus using the setpoints of the menu
2.5.2 instead of the ones of the menu 2.5.3).
DIF.2501 Inhibition of start. When the input is
“active”, the automatic start of the engine is
inhibited. The “REMOTE START” mode is not influenced by
this function.
DIF.2502 Inhibition of supply.
In automatic mode, when this input is “active”, the controller
opens GCB (but only if it can be re-closed, thus if a closure
command is configured).
DIF.2701 Enables remote start requests. If this function
is defined for one input, “REMOTE START”
function is inhibited if the input is not active.
DIF.2705 Disables protections on analogue
measures.
When this input is “activated”, the thresholds set on analogue
measures having bit 13 ON in the third configuration parameter
(see par. 5.6.2) do not trigger the relevant protections.
DIF.2706 Enables the commands by the serial ports. If this input is not active, the controls sent via Modbus
HOLDING REGISTER 101 and 102 are not accepted.
DIF.2709 Consent to start. In case of a request for automatic starting, the board activates
its internal sequence to start the engine, but it does not activate
any actual control until this input (if it exists) is activated (it can
be used, for example, to manage pre-ventilation).
DIF.3001 Status of GCB circuit breaker. YES It is used to detect the actual status of the KM/MCB circuit
breaker. In case of discordance between status and command,
a signalling will outline it.
DIF.3002 Status of ACB circuit breaker. YES It is used to detect the actual status of the KM/MCB circuit
breaker. In case of discordance between status and command,
a signalling will outline it.
DIF.3003 Status of BCB circuit breaker. YES It is used to detect the actual status of the KM/MCB circuit
breaker. In case of discordance between status and command,
a signalling will outline it.
DIF.3004 Status of LCB circuit breaker. YES It is used to detect the actual status of the KM/MCB circuit
breaker. In case of discordance between status and command,
a signalling will outline it.
DIF.3011 Trip of GCB circuit breaker. YES
Connect to this input the “tripped” contact of circuit breaker. If
the input is “active”, an alarm (block) with a fixed description
(language-dependant) is activated.
DIF.3012 Trip of ACB circuit breaker. YES
Connect to this input the “tripped” contact of circuit breaker. If
the input is “active”, an alarm (block) with a fixed description
(language-dependant) is activated.
DIF.3013 Trip of BCB circuit breaker. YES
Connect to this input the “tripped” contact of circuit breaker. If
the input is “active”, an alarm (block) with a fixed description
(language-dependant) is activated.
DIF.3014 Trip of LCB circuit breaker. YES Connect to this inp
ut the “tripped” contact of circuit breaker. If
the input is “active”, an alarm (block) with a fixed description
(language-dependant) is activated.