Fuji Electric Frenic lift Скачать руководство пользователя страница 186

Страница: 186 / 254

2.3 Overview of Function Code

hap.
2

FUN
CT

L97

Magnetic Pole Position Tuning (Voltage)

L97 specifies the amplitude of alternating voltage that is used magnetic pole position tuning

(L03=4).

L98

Protecting operation selection switch

E34 current detection (operation level 1)

E35 current detection1 (timer)

By setting L98 the inverter protecting functions can be enabled/disabled.

Bit

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Function

Not

assigned

FAN

ON/OFF

during

battery

operation

Not

assigned

Calculate

ASR with

only speed

command

during

ULC

ENOFF

signal

output

mode

Not

assigned

Drive

continuance

alarm

Over torque

current

protecting

operation

Data=0

Disable

Disable Disable

Disable

Data=1

Enable

Default

Set 0 for the not used functions.



Over torque current protecting operation (Bit 0)

The inverter stops when reference torque current of the inverter exceeds the over torque current

detection level (E34) and the reference torque current continues longer than the period specified by

over torque current detection time (E35). The state is reset after the inverter stops.

In case of vector control with PG for synchronous motor, the motor torque current is approximately

proportional to the output current of the motor. But in case of vector control with PG for

asynchronous motor the motor torque current is not proportional to the output current of the motor.



Drive continuance alarm (Bit 1)

If the function is enabled, the inverter keeps driving the motor for ten seconds when the following

alarm happen. This allows to stop safely the elevator when alarm happens.

OH2

(External alarm input 2

THR2

)

OH4

(Motor protection PTC thermistor)

OL1

(Motor protection Electronic thermal)

OLU

(inverter unit Overload)

Er6

(Reference torque decreasing command error)

Torque current
instruction value

E34

ALM

(

)

E35

2-173

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды