Fuji Electric Frenic lift Скачать руководство пользователя страница 79

Страница: 79 / 254

■

Input power limitation –

IPL

(Function code data = 112)

During battery operation

when the input power has exceeded the level specified C01 and the input power

continues longer than the period specified by C02 (Limit time) the inverter stops automatically and

IPL

turned ON. It turns OFF when FWD or REV command turns OFF.



For details, refer to the descriptions of function codes C01 to C02.

■

MC control 2 – SW52-3

(Function code data = 114)

This output signal is used for MC control. This signal is a logical sum (OR gate) of

SW52-2

(MC

control) and

AX2

(Run command activated).

Compared with

SW52-2

, even if

terminal is OFF or

terminal is ON,

SW52-3

comes ON and

MC can be turned ON as soon as run command is ON.



For details, refer to the descriptions of function codes L85 and L86 (MC Control).

■

Pole tuning done –

PTD

(Function code data = 115)

Pole tuning done with reference to Z-signal –

PTD_Z

(Function code data = 126)

If the Pole tuning is not done, the signal is OFF, therefore the drive is informing to the external equipment

that Pole tuning must be performed. If pole tuning is performed

PTD

signal is set to ON when the tuning

has been finished without errors. After that, when detecting a Z-phase pulse (or similar correction signal)

of AB-Z encoder,

PTD-Z

signal is set to ON. When any of the following condition is met, these signals

are reset.

- Power-off the inverter.
- The inverter tripped during the magnetic pole position tuning.
- Magnetic pole position tuning is canceled before ending.
- F42, P01, L01 or L02 is changed.

These signals show the status of magnetic pole position tuning as follow:

PTD

PTD-Z

State of the magnetic pole position tuning

OFF

Magnetic pole position tuning has not been completed

successfully.

OFF

Combination not possible.

OFF

Although the pole position tuning has been completed

successfully, Z-phase pulse has not been detected (correction

is not performed).

Magnetic pole position tuning has been completed

successfully, the correction by Z-phase pulse has been also

completed successfully.

2-66

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды