Fuji Electric Frenic lift Скачать руководство пользователя страница 180

Страница: 180 / 254

2.3 Overview of Function Code

hap.
2

FUN
CT

L85

MC Control (Startup delay time)

L86

MC Control (MC OFF delay time)

L85 and L86 specify the ON and OFF timings of the MC control signal

SW52-2

SW52-3

SW52-2

is assigned to a general-purpose, programmable output terminal by setting "12" in function

codes E20 to E24 and E27.

SW52-3

is assigned by setting “104” to them. The MC control signal

opens or closes the magnetic contactor connected between the inverter and motor.

■

Startup delay time (L85)

L85 specifies the delay time from when the MC control signal

SW52-2

turns ON until the main

circuit output gate turns ON.
- Data setting range:

0.00 to 10.00 (s)

Even if no

SW52-2

is assigned to a general-purpose programmable output terminal,

turning a run command ON turns the main circuit output gate ON after the delay time

specified by L85 elapses.

■

MC OFF delay time (L86)

L86 specifies the delay time from when the main circuit output gate turns OFF until the MC control

signal

SW52-2

turns OFF.

- Data setting range:

0.00 to 10.00 (s)

■

MC control

SW52-2

The table below lists the inverter running conditions and triggers required for turning the MC control

signal

SW52-2

ON or OFF. The timing diagram is shown on the next page.

SW52-2

OFF

Current status

retained

(1) When all of the following conditions

are met, turning a run command from

OFF to ON turns the MC control signal

ON.

- "Coast-to-stop"

OFF

- No trip

- Terminals [EN1]/[EN2] ON

- "Force to decelerate"

DRS

OFF

(2) Any of the following events with a run

command being ON turns the MC

control signal ON.

- "Coast-to-stop"

from ON to OFF.

- A trip that occurred is reset.

- Terminals [EN1]/[EN2] from OFF to

Any of the following events with the

MC control signal being ON turns the

MC control signal OFF after the MC

OFF delay time specified by L86.

- Inverter main circuit output gate

from ON to OFF

- Run command from ON to OFF with

the inverter main circuit output gate

being OFF

- "Coast-to-stop"

from OFF to ON

- A trip occurs.

- Terminals [EN1]/[EN2] from ON to

OFF

- "Force to decelerate"

DRS

from OFF

to ON (below the stop speed).

Except the

conditions listed

at left

* When the conflicting conditions are present, e.g., from ON to OFF conditions and from OFF to

ON conditions, the latter event has priority.

* The

and [EN

1]/[EN2]

are in normal logic.

* The "Force to decelerate" state is kept from the entry of a

DRS

command until the

DRS

is turned

ON, and the run command and inverter main circuit output gate are turned OFF.

2-167

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды