Fuji Electric Frenic lift Скачать руководство пользователя страница 82

Страница: 82 / 254

2.3 Overview of Function Code

hap.
2

FUN
CT

E30

Speed Arrival (Hysteresis)

H75 (Speed Agreement, Delay time)

E30 specifies the detection range of the speed arrival signal.
- Data setting range: 0.00 to 6000 (r/min)



Data setting range changes depending on the number of poles of motor etc. For details, refer to

section 2.2.

■

Output signals "Speed arrival

FAR

", "Speed arrival 3

FAR3

", "During acceleration

DACC

" and "During deceleration

DDEC

The output signal

FAR

can be assigned to a general-purpose, programmable output terminal by

setting "1" (E20 to E24 and E27). The

FAR

comes ON when the detected speed against the reference

speed (pre-ramp) is within the specified range. However, if the run command is OFF or the reference

speed (pre-ramp) is less than 0.00 (r/min) (less than the stop speed), it will not come ON.
The output signal

FAR3

can be also assigned by setting "72." The

FAR3

comes ON when the

detected speed against the reference speed (pre-ramp) is within the specified range. This output

signal is not affected by any run command.
The output signals

DACC

and

DDEC

can be also assigned by setting "73" and "74," respectively.

The

DACC

DDEC

comes ON depending on whether the motor is accelerating or decelerating by

comparing the reference speed (pre-ramp) with the detected speed. These output signals during

accelerating and decelerating are turned OFF according to the level of the speed arrival hysteresis

specified by E30.

When the output signals

FAR

DACC

and

DDEC

are assigned, the ON-to-OFF delay

time can be specified by function code H75 in order to prevent chattering. H75 can be

used for the output signal

DSAG

When the torque vector control is selected reference speed (final) is used instead of

detected speed.

Following is a timing chart for these output signals.

E30

FWD

FAR

FAR3

DACC

DDEC

H75

Speed

Detected

speed

Refference speed
(pre-ramp)

2-69

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды