2-16
Code
Name
Data setting range
Incr
em
ent
Un
it
C
hang
e
w
h
en
runni
ng
Da
ta
cop
yin
g
Default s
e
ttin
g
Data f
o
rm
a
t No.
To
rq
ue v
e
ctor
contr
o
l
Softw
ar
e ver
si
on
wh
ich
ca
n b
e
used
y21
CAN Communication
(Node-ID)
1 to 127
1
-
N
Y
1
1
Y
y24
(Baud rate) 0: 10 kbps
1: 20 kbps
2: 50 kbps
3: 125 kbps
4: 250 kbps
5: 500 kbps
6: 800 kbps
7: 1 Mbps
1
-
N
Y
3
1
Y
y25
(User-defined I/O parameter 1)
0000
H
to FFFF
H
-
-
N
Y
0000
H
1
Y
y26
(User-defined I/O parameter 2)
-
-
N
Y
0000
H
1
Y
y27
(User-defined I/O parameter 3)
-
-
N
Y
0000
H
1
Y
y28
(User-defined I/O parameter 4)
-
-
N
Y
0000
H
1
Y
y29
(User-defined I/O parameter 5)
-
-
N
Y
0000
H
1
Y
y30
(User-defined I/O parameter 6)
-
-
N
Y
0000
H
1
Y
y31
(User-defined I/O parameter 7)
-
-
N
Y
0000
H
1
Y
y32
(User-defined I/O parameter 8)
-
-
N
Y
0000
H
1
Y
y33
(Operation)
0: Disable
1: Enable (CiA 402)
-
-
N
Y
0
1
Y
y34
(Communications error processing)
This function code is valid in case of y36=-4 or -5
0: Set the motor immediately in coast-to-stop mode and trip
with Ert.
1: After the time specified by y35, coast to a stop and trip with
Ert.
2: If the inverter receives any data within the time specified
by y35, ignore the communications error. After the
timeout, coast to a stop and trip with Ert.
3 to 15: Same as y34=0
-
-
Y
Y
0
1
Y
y35
(Communication time-out
detection timer)
0.0 to 60.0
0.1
s
Y
Y
0.0
3
Y
y36
(Operation selection in abort status)
-5 to 3
1
-
Y
Y
1
2
-
y37
(Compatibility selection)
0: Standard
1: Compatible with FRENIC-Lift (LM1)
-
-
N
Y
0
1
-
y41
Setting method of speed command by
communication
0: Speed command
1: Acceleration command
-
-
N
Y
0
1
-
y95
Data clear processing for
communications error
0: Do not clear the data of function codes Sxx when a
communications error occurs. (compatible with the
conventional inverters)
1: Clear the data of function codes S01/S05/S19 when a
communications error occurs.
2: Clear the run command assigned bit of function code S06
when a communications error occurs.
3: Clear both data of S01/S05/S19 and run command
assigned bit of S06 when a communications error occurs.
* Related alarms: Er8, ErP, Ert
-
-
Y
Y
0
1
Y
y97
Communication data storage selection
0: Store into nonvolatile memory (Rewritable times are
limited)
1: Write into temporary memory (Rewritable times are
unlimited)
2: Save all data from temporary memory to nonvolatile
memory (After all save, return to Data 1)
-
-
Y
Y
0
1
Y
y99
Loader Link Function
(Mode)
Control command
Run command
-
-
Y
N
0
1
Y
0:
Follow H30
Follow H30
1:
Via Loader
Follow H30
2:
Follow H30
Via Loader
3:
Via Loader
Via Loader
Note: Control commands include Speed command, Torque
current command, and Torque bias command.
Содержание Frenic lift
