Fuji Electric Frenic lift Скачать руководство пользователя страница 184

Страница: 184 / 254

2.3 Overview of Function Code

hap.
2

FUN
CT

L90

PG abnormal (operation choice)

H76 PG abnormal mode 3(detection range)

H77 PG abnormal mode 3(detection timer)

L91

PG Error Detection (Detection level)

L92

PG Error Detection (Detection time)

L90 to L92 specify the PG error detection conditions and the inverter operation in case of error. If

the speed error is within a domain specified by L91 during the detection time specified by L92, the

inverter regards it as an error and continues running or stops with/without an alarm according to the

mode specified by L90.
- Data setting range (L91): 0 to 50 (%)

(L92): 0.0 to 10.0 (s)

In the above figure,



through



represent the following states.



: The phases A and B of the PG are reversely connected.



: Excessive speed deviation (|Detected speed| > |Reference speed (final)|)



: PG wires broken (During zero speed operation, that is, at -0.1 to +0.1 Hz, no PG error can be

detected.)



: Excessive speed deviation (|Reference speed (final)| > |Detected speed|)

If L90 = 0

When the speed is within domains



through



in the above graph, the inverter regards it as an

error. Independent of the PG error detection, the inverter continues to run.
If a PG abnormal signal

PG-ABN

is assigned to any general-purpose, programmable output terminal

by setting E20 to E24 and E27 to “76”, the inverter turns the

PG-ABN

ON.

If L90 = 1

When the speed is within domains



through



in the above graph, the inverter regards it as an

error and stops with an excessive speed deviation error (

ErE

If L90 = 2

When the speed is within domains



through



in the above graph, the inverter regards it as an

error and stops with an excessive speed deviation error (

ErE

If L90 = 3

When the speed is within domains



through



in the above graph, and when the speed is within

domains





in the above graph, the inverter regards it as an error and stops with an excessive

speed deviation error (

ErE

Reference

speed

(final)

Detected speed

Detection

level

③

②

①

④

⑦

⑧

⑤

⑥

-0.1 to +0.1Hz

L91

L90 = 0,1,2

Figure 1

Figure 2

Reference

speed

(final)

Detected speed

Detection

level

③

②

①

④

⑦

⑧

⑤

⑥

-0.1 to +0.1Hz

L91

Detection

Level (H76)

Detection

Level (H76)

L90 = 3

2-171

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды