Fuji Electric Frenic lift Скачать руководство пользователя страница 178

Страница: 178 / 254

2.3 Overview of Function Code

hap.
2

FUN
CT

■

Brake check time (L84)

L84 specifies the allowable time for the

BRKE

signal to turn ON (OFF) after the

BRKS

signal is

turned ON (OFF). If the ON (OFF) state of the

BRKE

signal does not match that of the

BRKS

signal

within the time specified by L84, the inverter trips with alarm

Er6

. For confirming MC operation,

taking use of timer for confirming the condition of

SW52-2

and

CS-MC

- Data setting range: 0.00 to 10.00 (s)



Refer to the descriptions of function codes L84 to L86 for details.

Brake control signal

BRKS

Setting "57" to any of the general-purpose, programmable output terminal (by E20 to E24 and E27)

assigns the

BRKS

signal to that terminal. The

BRKS

signal is available in two modes specified by

L80.
The

BRKS

signal turns OFF when the time length specified by L83 elapses after the speed (< stop

speed) drops below the stop speed, independent of a run command. Adjust the braking timing to

match the running pattern.
If the

BRKS

signal turns OFF with a run command being ON, the

BRKS

signal will no longer turn

ON again even the ON conditions are met again. To turn the

BRKS

signal ON again, turn the run

command OFF once.

Brake confirmation signal

BRKE

Setting "65" to any of the general-purpose, programmable input terminal (by E01 to E08, E98 and

E99) assigns a

BRKE

signal to that terminal. This signal is used to confirm whether the actual brake

works normally with the

BRKS

signal issued from the inverter. Configure an external circuit that

turns the signal ON or OFF when the brake is actually released or applied, respectively.
If there is a time lag between the status change of the

BRKS

signal and the corresponding change of

the

BRKE

signal, specify the lag time with L84 (Brake check timer). During the lag time set by L84,

even if there is a difference between the output status of the

BRKS

signal and input status of the

BRKE

signal, the inverter does not trip. If the output status of the

BRKS

signal is not identical with

the input status of the

BRKE

signal after the time set in L84 elapses, the inverter trips with alarm

Er6

. Note that the time lag function does not work unless

BRKS

and

BRKE

are specified.

Make sure that the total time of the brake check time (L84) and the OFF delay time (L83) is less than

the stop speed holding time (H67).

2-165

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды