Fuji Electric Frenic lift Скачать руководство пользователя страница 183

Страница: 183 / 254

L87

Door Control (Door open starting speed)

L88

Door Control (Door open delay time)

L89

Door Control (Door open period)

L87 to L89 specify the door open parameters relating to the door control signal

DOPEN

that is

assigned to a general-purpose, programmable output terminal by setting "78" with E20 to E24 and

E27.

■

Door open starting speed (L87)

L87 specifies the reference speed (final) below which the door control signal

DOPEN

is turned ON.

The

DOPEN

is turned ON actually after the door open delay time specified by L88 elapses.

- Data setting range: 0.00 to 6000 (r/min)



Data setting range changes depending on the number of poles of motor etc. For details, refer to

section 2.2.

■

Door open delay time (L88)

L88 specifies the delay time from when the speed drops below the door open starting speed (L87)

until the

DOPEN

signal is turned ON.

- Data setting range: 0.0 to 10.0 (s)

■

Door open period (L89)

L89 specifies the period during which the

DOPEN

is kept ON.

- Data setting range: 0.1 to 30.0 (s)

Door control

When the reference speed (final) drops below the door open starting speed (L87) during deceleration

and the door open delay time (L88) elapses, the

DOPEN

is turned ON and kept ON during the door

open period (L89).

Time

Speed

L88

：

Door control

(Door open

delay time)

L89

：

Door control

(Door open

period)

Digital output

DOPEN

L87

：

Door control

(Door open

starting speed)

OFF

Increasing the reference speed (final) above the speed (L87) with the

DOPEN

being OFF activates

the

DOPEN

ON process judgment. If the reference speed (final) does not exceed the speed (L87),

the L88 and L89 specifications will be ignored so that the

DOPEN

will be kept OFF.

Decreasing the reference speed (final) from the speed exceeding the L87 down to less than the L87

activates the delay timer (L88). After the delay time (L88) elapses, the

DOPEN

turns ON during the

door open period (L89).
This door control applies to also the battery operation. When the battery operation speed does not

reach the door open starting speed (L87), the

DOPEN

will be kept OFF.

Note: When the L87 = 0.00, the

DOPEN

does not work. Operation is different according to L99

bit6.



Refer to the descriptions of function codes L99 bit6 for details.

2-170

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды