Fuji Electric Frenic lift Скачать руководство пользователя страница 194

Страница: 194 / 254

2.3 Overview of Function Code

hap.
2

FUN
CT

L101

Unlock Safety Gear (Operation)

E01 to E08 Command Assignment to [X1] to [X8]

L102

Unlock Safety Gear (Level)

L103

Unlock Safety Gear (Pluse time)

L104

Unlock Safety Gear (Rest time)

L105

Unlock Safety Gear (Pluse)

L106

Unlock Safety Gear (Speed limit)

F03 Rated Speed

The aim of “Unlocking safety gear” function is to electrically unlock the car from a safety gear lock.

Inverter will generate current pulses in order to force an abrupt reaction of the motor. The abrupt reaction

of the motor will unlock the safety gear.

■

Unlock Safety Gear Operation (L101)

L101 specifies the operation of unlock safty gear function.
- Data setting range: 0 Disable

1 Enable

■

Unlock Safety Gear Level (L102)

L102 specifies the amplitude of current pulses. This value is a percentage of the inverter’s rated

current.
- Data setting range: 10 to 200 %

■

Unlock Safety Gear Pulse time (L103)

L103 specifies the time that inverter will apply the current of the value set on L102.
- Data setting range: 0.1 to 2.0 s

■

Unlock Safety Gear Reset time (L104)

L104 specifies the time between two consecutive pulses.
- Data setting range: 0.1 to 1.0 s

■

Unlock Safety Gear Pulse (L105)

L105 specifies the number of pulses that inverter will generate after L101 is enabled and RUN

command is given.
- Data setting range: 1 to 5

■

Unlock Safety Gear Speed limit (L106)

L106 specifies the maximum speed that the inverter will allow the motor to turn during Unlock safety

gear operation.

- Data setting range: 0 to 6000 rpm

Operation procedure

(1) Set function code L101 to "1" or turn ON

ULSG

command during stop.

(2) When a run command is set, Unlock safty gear operation stars.

(3)

The

operation is performed according to preset parameters, and ended automatically.

(4) Turn OFF the run command to finish the operation.

If the run command is given by keypad, it will become OFF automatically.

This function cannot be used unlimited times. If after 2 or 3 trials car is not unlocked, unlock the car

by means of mechanic devices (i.e. hoist). An unlimited use of this function can lead an inverter

failure.

An accident or physical injury may result.
An damage may result.

2-181

Содержание Frenic lift































































































































































































































































Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды

Fuji Electric Frenic lift, Справочное руководство

Результаты поиска

Содержание Frenic lift

Отзывы:

Похожие инструкции для Frenic lift

Бренды по названию

Популярные бренды